Amercoat Chemical Resistant Lining. Product Data/. Application Instructions. • High Solids, high performance epoxy novolac also defined. Amercoat – Download as PDF File .pdf), Text File .txt) or read online. This Safety Data Sheet is prepared in accordance with Annex II to Regulation ( EC) No. / AMERCOAT CHEMICAL LINING CURE.
|Published (Last):||7 January 2014|
|PDF File Size:||11.25 Mb|
|ePub File Size:||4.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
This Section includes the flowing: We take conventional alkyd chemistry and emulsify it in water to deliver a unique More information. High pressure fresh water cleaning. Discoloration and normal chalking does not impact performance. If thinning is desired, use Amercoat 15 mineral spirits. Amercoat A may be used as a pit filler for certain amrcoat. When properly used, Amerase will not damage surfaces coated with Amerase or PSXeven after repeated cleaning.
Thinner Amercoat is typically used without thinning.
We take conventional alkyd chemistry and emulsify it in water to deliver a unique. Waterproofing System for Wastewater Tanks in Petrochemical Industries and Refineries Introduction Wastewater of petrochemical industries and refineries contains amercoa amounts of emulsified aliphatic or.
Prepare damaged areas to original surface preparation specifications, feathering edges of intact coating.
Amercoat – [PDF Document]
Thicker films will require longer dry times since the product requires moisture to cure. Refer to Information Bulletin for further information on prevention of amine blush.
Alkyd coatings and waterborne arcylic coatings should be applied after the film is dry through and no greater than three times the dry through time. Do not allow Prep 88 to dry on the surface.
Refer to this product amfrcoat MSDS before using this material. Surfaces to be coated must be primed in accordance with the Hi-Temp product data sheet. When using amercat flake additive a spray tip size of X. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. It is highly advisable to rinse the steel prior to topcoating when steel will be subject to ponding water or condensation from high humidity conditions in service.
The A component is the same for Amerlock and Amerlock 2. Surface temperatures must be measured at various elevations from top to bottom and in each cardinal direction. Furnish all labor, materials, tools and More information.
Protective Coatings Product Catalog AMERCOAT. A PPG brand
PSX should be amfrcoat to reach a Dry-to-Touch condition before force curing above F Area should be sheltered from airborne particulates and pollutants.
Ensure good ventilation during application amercozt curing. Characteristics – Direct application to ambient steel – Direct application to hot steel having a metal temperature up to F C – Corrosion resistant to F C – U. Liquid, powder, and activator are packaged in the correct proportions which, when mixed together, yield 0. If thinning is desired, use Amercoat 65 xylene.
For automatic application a substrate temperature of 86 F 30 C is recommended The temperature of the substrate should be at least 5 F 3 C above the dew point.
Amercoat 253 pdf
There is no data available for this product. General air quality Area should be sheltered from airborne particulates and pollutants. Ensure the surface ph has been neutralized 7. Mild Steel Remove all loose rust, dirt, grease or other contaminants by one of the following depending on the degree of cleanliness required: Check the dry film thickness regularly.
Call for prices Details. Maximum F unless a lower maximum is specified General air quality Area should be sheltered from airborne particulates and pollutants. Store product in dry conditions at temperatures of F. Pour the liquid into the mixing vessel. Pacific Southwest Coatings specializes in performance coating solutions for corrosion, abrasion, extended life cycle performance, marine, offshore, chemical containment, biological containment, high temperature, fire protection and commercial architectural specialty applications.
Steel Round off all rough welds and sharp edges. Thinner Cleaning solvent Safety precautions Do not thin Amercoat Water based cleaner For paint and recommended thinners see safety sheetand relevant material safety data sheets This is a solvent zmercoat paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes.
Or see instructions for specific primer Apply PSX as soon as possible to prevent the blasted surface from rusting. Limitations for use Safety precautions For Industrial or Professional Use Only For paint and recommended thinners see safety sheetand relevant material safety data sheets This is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes.
Maximum recoating time is highly dependent upon actual surface temperatures not simply air temperatures. Offshore Information Sheet No.
Commercial Fishing Supplies | Seattle Marine & Fishing Supply Co.
When this is impossible or impractical, Amerlock can be applied over mechanically cleaned surfaces. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such use or the contents of this information unless there are written agreements stating otherwise. Agitate with a power mixer for minutes until completely mixed.
Powder 24 months from date of manufacture when stored indoors in the original unopened container. Blast with an angular abrasive to yield a surface profile of mils. Do not rake joints.