AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Dill Diran
Country: Republic of Macedonia
Language: English (Spanish)
Genre: History
Published (Last): 16 October 2007
Pages: 272
PDF File Size: 4.27 Mb
ePub File Size: 16.25 Mb
ISBN: 724-5-76524-461-6
Downloads: 64179
Price: Free* [*Free Regsitration Required]
Uploader: Yozshubar

At this point channel one will begin to distort. The amplifier can operate at practically any power level without risk of overheating. This fan is used to cool the internal parts of the amplifier when in use. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack. Connect an input signal to channel one. Risiko – Elektrischer Schlag! You may also visit us on the web at www. Amplifiers arrive to you preset in the stereo operation mode.

Channel 2 Frequency Adjustment. Clipping should be kept to a reasonable minimum. You’re reading an excerpt. Refer all servicing to qualified service personnel. Banana Plugs – When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are completely screwed in. Connect your speaker across the red output binding post on the rear of your amplifier.

These fans are used to cool the internal parts of the amplifier. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal.

Typical speaker output using bare wire. Turn channel two gain up. Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage. The unit also provides a way to rear mount the unit into a rack for added security.

  CARTE DE BUCATE PENTRU DIABETICI PDF

VLP1000 power amplifier

Insert bare wire into the binding post and tighten. Cooling Fan Dual speed cooling fans. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

This amplifier is designed to mount into a standard 19″ rack. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.

Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. All channel output during the “Short Circuit Protection” will be interrupted i.

Never block the fan grills in amefican way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

No user serviceable parts inside. Every Vplus series amplifier has been thoroughly tested V and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. Auido speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. Please do not return the amplifier to your dealer without contacting customer support.

AMERICAN AUDIO V POWER AMP AMPLIFIER WATTS NR! | #

When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. Channel 1 filters is control by dip switch 1 and channel 2 filter is controlled by dip switch 4. Turn your input source level up.

  ELECTRONICA ALLAN R.HAMBLEY PDF

The diagram below detail the functions of each dip switch, the functions are also printed on the rear panel of the amplifier. Except for an occasional flash, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel.

Low Cut Frequency Selector When the Low Cut Filter is activated, dip switches 2 channel 1 and 3 channel 2 will control the frequency roll-off.

American Audio V1000 PLUS Manuals

If your speaker lines short, the amplifier automatically detects this problem and discontinues operation for that channel. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. Connect your inputs into channels one and two of the amplifier.

Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of auvio problems. Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads.

During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible. Turn your amp americzn. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. These amplifiers are designed to provide a big impact in sound reproduction. Before using this amplifier, read the user manual for further warnings.

Connect your speakers to the outputs on the rear of the amplifier.