CELIT 4D PDF

Celit 4D. Done. Comment. views. 0 faves. 0 comments. Taken on August 20, Some rights reserved. Flickr is almost certainly the best online photo management and sharing application in the world. Show off your favorite photos and videos to the world, securely. Détail pieds de mur 1 Lattage vertical 22/45 2 Celit 4D 23mm 3 structure en bois mm FJI 45/ 4 latte inférieure en Kerto 27/ 5 poutre / 6 plat en.

Author: Mezijas Zurg
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Politics
Published (Last): 1 May 2011
Pages: 118
PDF File Size: 4.31 Mb
ePub File Size: 7.25 Mb
ISBN: 366-2-38454-123-8
Downloads: 91915
Price: Free* [*Free Regsitration Required]
Uploader: Zulkir

Also the openings on both sides of the cavity need to be big enough otherwise they will hinder the airflow or even stop it.

Menisoss sprl

The first and the last profile of the roof are the special fixture profiles. After celti and having mounted the second profile, we repeat the procedure to mount the rest of the profiles. Introduction Traditional roofs with tiles are ventilated roofs. Omega profiles that will be placed in between 2 panels in order to collect the rain water that may flow in the vertical space between 2 panels. The figures below show the positions and number of these profiles.

Systeemoplossingen Ontdek vaak voorkomende bouwsystemen met onze systeemoplossingen. A schematic overview of the construction is given next: In general an air-cavity of around 50 mm will give an air flow that is enough to ventilate the heat away.

Hoogkwalitatieve bio-ecologische, houtbouw- en isolatiematerialen, met deskundig advies voor vakman en consument. Schrijf u in op onze nieuwsbrief en ontvang periodiek info over onze producten, info over opleidingen en nieuwtjes. Ceilt een zeer grote marktvraag naar houtbriketten en -pellets zijn de Ecopower houtbriketten niet meer leverbaar op korte termijn. The aim of this guideline is not focused on the installation process of the BIPV modules, but the construction process of the substructure needed to install them.

  DENTRO LA GLOBALIZZAZIONE BAUMAN PDF

Celit 4D | Peter Steen en CO | Flickr

The vertical profiles are place on top of the beams to have maximum strength. Bio-ecologische houtbouw- en isolatiematerialen, deskundig advies voor vakman en consument Bezoek onze webshop. Special fixture D4 types of profiles: Nevertheless, the components, materials and their installation process may vary in different cases, thus the information provided in this document should be handled with care, adjusting the installation with regard to the existing roof composition in each case.

Picture of the first produced module. A schematic overview of the construction is given next:. The house has a roof and a facade. More detailed, the vertical profiles are mounted with screws over the wooden profiles and the Omega profiles on the roof surface alternately every 70 cm.

The profiles can easily screwed in the wooden bat. The house has a roof and a facade. The roofing substructure is composed by an insulation material, a set of wooden vertical profiles and a metallic construction support system where the BIPV roofing shingles are installed. In this Belgium demo building we demonstrate the RS02 solar eclit elements.

The basic construction and the materials for construction are described in guideline b1.

Construction design RS02 – BFirst

The vertical distance between 2 ALUTEC RL profiles is of the highest importance because this space must allow inserting the panel but must also make sure that the panels will be difficult to remove by the wind. Examples of non-ventilated asphalt shingle and ventilated tiles roofs.

The modules are slided in the horizontal profiles and fixed with the use of EPDM joins: Three types of profiles: Wurtz screws are used to attach these aluminum profiles to the wood structure. The mounting of the horizontal profiles on the vertical ones is done by the retaining clips, as shown in the picture below.

  MAINDA SAIN PDF

Installation of the modules After the framework is installed, we start placing the modules. Installation of profiles on the roof The vertical profiles are place on top of the beams to have maximum strength. Not all roofs have this construction.

The house has a roof and a facade. In this Belgium demo building we demonstrate the RS02 solar roof elements. The ventilation cavity will transport water-vapour from the construction to cepit outside.

For easy mounting an extra vertical wooden bat is placed on top of the Celit 4D at the location of the underlaying beam. Roof details of the demo house in Mons B. Vul hier het contact formulier in en we contacteren u zo spoedig mogelijk.

This is an h1 heading

Installation of the vertical profiles on the wooden beams Three types of profiles have been used: The construction of the cavity needs enough space at the lower and the upper part of the roof. The modules are slided in the horizontal profiles and fixed with the use of EPDM joins:. A well insulated roof like most roofs since has a risk of internal condensation.

Additional T joins are placed to avoid movement by strong wind. Roof layers The construction is built up in different layers: