Where could I find the manual for epox ep af sli2?. EPoX EP-8K3A+ – motherboard – ATX – Socket A – KT overview and full product specs on CNET. Model EP-8K3A+. EPoX EP-8K3A+ Manual Settings. Epox EP-8K5A2+ Official Product Page · Epox EP-8K5A3+ Official Product Page · 8K5A Series Manual .pdf format) high temp readings on the 8K3A series mobos since they were actually reading from the internal diode and.

Author: Shakale Yojin
Country: Tunisia
Language: English (Spanish)
Genre: Environment
Published (Last): 25 May 2004
Pages: 377
PDF File Size: 11.89 Mb
ePub File Size: 2.43 Mb
ISBN: 152-5-73184-371-9
Downloads: 6694
Price: Free* [*Free Regsitration Required]
Uploader: Tolmaran

Latency on the memory increases actually negating some of the new bandwidth performance you get.

EPoX EP8K9A User Manual

System Memory Configuration VT brings a few important upgrades to the table over the VT series of bridges used since KT Think about it like that and you see why the figures are so close together. Click to find out more. Overclocking I wont dwell on overclocking for long except to prove the effect of overclocking the mankal side bus and letting the CPU have ep-8ka bandwidth.

Onto the memory benchmark figures from Sandra. In the following graph, all that is changed is the memory clock via a reboot.

The results are higher than any KTA results we’ve seen, although only by very small amounts which again highlights something we’ll touch on in the conclusion so keep reading.

EPoX EP-8K3A+ – motherboard – ATX – Socket A – KT333

Layout is sensible despite with a couple of niggles that are mostly personal rotated socket and slightly goofy ATX power socket placement. Page 80 Appendix Partition 1. Lately during the filling cycle water hammer is occurring.

A 60 point gain I measured over points from some runs doesn’t seem like very much but it happens every time showing you that the memory bandwidth we have extra e-8k3a KT is helping performance.


Step Installation Easy Installation Procedure The KT Northbridge seems to run exceptionally cool. Partition To Partition 2.

EPoX EP-8K3A+ – motherboard – ATX – Socket A – KT Overview – CNET

nanual AGP supports 1x, 2x 3. So we’ll take a look at performance from a number of angles. Sure it leaves some free for the rest of the system to utilise, but by and large the headroom doesn’t make much difference.

Click to find out more. Apart from that, the board is quite fully featured. Starting in the top left area we have the main ATX power connector and the 3-phase power regulation circuitry and components that feed the CPU socket with power and in turn the rest of the board.

Drivers Installation Speak Configutation: The Northbridge is only passively cooled with no noisy fan which is a bonus. Speed will increase by multiplier only. Got it, continue to print.

Here’s a link to this great service Good luck! How can this be resolved. It’s one of the most stable boards I’ve yet seen, something I maybe couldn’t say about EPoX ep-8k3w the past. I was a bit hasty in releasing a review of the board where I could see no discernable difference in the two modes since other reviews had shown a difference and a chat with EPoX UK assured me the board did run asynchronous.

Given a fast graphics card, you are able to see the effect that memory bandwidth has on the system when you use Quake3. What was the best tech product of ?

I need all the help i can manuak It’s this graph that most people are going to see and think, “what’s the benefit of running DDR then? The email address entered is already associated to an account.


These are going to show the same numbers that any well sorted Socket A board will show for the same processor, in our case the Ep8k3a MHz. Page 65 Drivers Installation General: I’ll skip the CPU Multimedia numbers except to say that there is a very small but detectable rise in the results when you go up to asynchronous mode.

Overall very fast, very stable and just what the overclocking doctor ordered. Latency on DDR memory subsystems actually increases ep–8k3a you run asynchronous to the front side bus, negating some of the performance, but on the whole performance rises.

Your answer needs to include more details to help people.

Review: EPoX 8K3A – Mainboard –

Add to my manuals Add. Don’t show me this message again. I can then sign out. These specifications are subject to change without notice. Of course you are also free to run your clocks synchronously and indeed this can possibly be advantageous since running asynchrously increases memory latency on a DDR memory subsystem.

The floppy and IDE connectors are placed, ideally for this reviewer at least, on the right hand vertical edge of the board and aligned vertically. We’ve had the board for a little while but manua, never been able to make the board work in asynchronous mode and detect any performance increase.