HT12D DATASHEET IN PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. HT12D Datasheet, HT12D Holtek Decoder Datasheet, buy HT12D Decoder IC.

Author: Kazrazragore Kajihn
Country: China
Language: English (Spanish)
Genre: Health and Food
Published (Last): 24 January 2011
Pages: 34
PDF File Size: 4.38 Mb
ePub File Size: 5.29 Mb
ISBN: 887-1-64960-602-3
Downloads: 26252
Price: Free* [*Free Regsitration Required]
Uploader: Vibar

This oscillator can be used by connecting these two pins through a 1M Resistor. Supply voltage; 5V 2. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

TL — Programmable Reference Voltage. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. They can also be connected to LED to physically view the received data.

This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. What is Web Browser. They are paired with 2 12 series of encoders. The 4-bit data that is received can be obtained on pins AD0 datasheeet AD1 and an address of 8-bit has to be set using the pins A0 to A7.

For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. Valid transmission; active high.

  LIVRO ANJOS CABALISTICOS MONICA BUONFIGLIO PDF

Choosing Battery for Robots. The serial input data is compared with the local addresses three times continuously.

Connected to daatasheet Ground of circuit. These are the 8-bit address bits, which is used to protect your data. Interface GPS with Arduino. It is mainly provided to interface RF and infrared circuits.

The IC has a built in oscillator.

It is not mandatory to use it. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.

Virgin H1t2d — Commercial Space Flight. Arduino based GPS receiver. A dafasheet circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

ddatasheet Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. A valid transmission in indicated by a high signal at VT pin. If you want security you can connect any of the 8 pins to 5V to make it high.

It is very important that your Decoder should have the same address of that of the encoder. The input data code is decoded when no error or unmatched codes are found. The Encoded 12 bit output data obtained from HT12E has to be given here.

Submitted by admin on 27 October Interface SD Card with Arduino. This pin will go high when a data is received. SPI Module of Arduino. We should set the bits in same pattern on Encoder and Decoder IC to pair them. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data datasheef. If any valid data is received they daatasheet be obtained from these four pins.

  80 DE RUGACIUNI FACATOARE DE MINUNI PDF

HT12D Decoder IC

These two ICs together form an Encoder and Decoder pair. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

This high-density System-in-Package SiP integrates controller, power switches, and support components. To know how a 4-bit data can be encoded and then send to the hr12d pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

HT12D/HT12F – Product Details – Holtek

Skip to main content. The data on 4 bit latch type output pins remain unchanged until new is received.

In simple terms, HT12D converts the serial input into parallel outputs. This pin powers dataeheet IC should use only 5V. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

Choosing Motor For Robots.