Interzinc B. Storage Conditions: All painting materials shall be stored in a clean, dry, well ventilated place, protected from sparks, flame. A three component, metallic, zinc rich epoxy primer which passes Slip B coefficient. Interzinc B complies with SSPC Paint 20 and contains minimum 80%. Interzinc Call for Price. A two component high solids, low VOC metallic zinc- rich epoxy primer formulated on proprietary polymer technology which provides.
|Published (Last):||2 January 2010|
|PDF File Size:||13.97 Mb|
|ePub File Size:||6.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Items specified or provided with factory finish; materials and products having factory-applied primer are not considered factory finished. The Manufacturer’s quality management system must be assessed and registered by an independent registrar as conforming to the requirements of ISO Wood, plaster, concrete, concrete masonry walls, ceilings, soffits, walkways, curbs, steps.
Maintain environmental conditions temperature, humidity, and ventilation within limits recommended by manufacturer for optimum results. Commencement of application is acceptance of substrate. Interior environment with high humidity and exposure to air pollution.
Deliver materials in manufacturer’s original, sealed, undamaged container with identification label intact. Retain only coating systems specified and delete all others.
Mild Atmosphere Applications- Urban and industrial atmospheres. Regional Materials- 20 percent extracted, processed and manufactured regionally: All batch number, product identification and quantities shall be recorded on appropriate QC documents.
Verify that substrate and workspace temperature and humidity conditions are in accordance with requirements of this section. High Performance coatings applied in the field with Company specializing in manufacturing products listed in this section with a minimum of ten 10 years documented experience. At project closeout, provide to Owner or Owners Representative an executed copy of the manufacturer’s standard limited warranty against manufacturing defect, outlining its terms, conditions, and exclusions from coverage.
SECTION HIGH PERFORMANCE SPECIALTY COATINGS
All products listed in this section must be manufactured under the appropriate follow-up service with each container bearing the certified label mark.
Protect work area from windblown dust and rain. Apply approved primer to properly cleaned substrate in accordance with manufacturer’s application instructions. Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
Intrezinc agreed upon in writing it serves as a guide for the finished work. Pipes, ducts, conduits, hangers and supports, interzibc, and equipment enclosures exposed to weather or view – corrosion-resistant finish. Information must demonstrate equivalence of product and performance to the specified material and complete systems.
Substrate and air temperature shall be in accordance with the manufacturers requirements. Upon completion of installation, all excess material, overspray and debris must be cleared and removed from the job site. Structural steel and framing with reference to primer receiving fire protection materials.
Interzinc B – A k i r a
If this location falls within interznic mile radius of the project site, then Interchar can contribute to earning Materials and Resources Credit 5. No coating material may be procured or delivered to the project site prior to the review and acceptance of the proposed materials by the Architect in writing.
Submit plan, section, elevation and perspective drawings as necessary to depict system configuration, design considerations and application procedures. International Paint, LLC, which is located at: Do not commence application of coatings until the contractor, applicator and inspector have examined the surfaces to receive Work in this section, and determined that the surfaces are acceptable to receive the specified materials.
This section is based on the products of International Protective Coatings, which is located at:. All surfaces to receive coatings must be clean, dry and free of oil, grease, loose mill scale, dirt, dust or other foreign substances which would impair bond of the material to the substrate. Interior environments with permanent condensation and pollution. To be selected by Architect from manufacturer’s full range of available colors.
Do not apply coatings under environmental conditions outside manufacturer’s absolute limits. Before proceeding with the work, the applicator will apply the primer and finish coat to a representative substrate section of integzinc feet in size. Final color, gloss and finish will be determined and interzind by the Architect. Requests for substitutions must be made 30 days prior to submittal and contain the full name of each product, descriptive literature, testing data collected from industry consensus standard testing, data on past performance, manufacturer’s instruction for use and generic type.
Marine, offshore and coastal areas inyerzinc high salinity. Submit manufacturer’s written installation instructions. If necessary for job schedule, the General Contractor shall provide enclosures and heat to maintain proper temperatures and humidity levels in the application areas.